Equipment Repair

We specialize in the repair of:

Cleaning Equipment
  • Walk-Behind Scrubbers
  • Carpet Extractors
  • Electric Swing Machines
  • Floor Buffers
  • Floor Sweepers
  • High Speed Floor Polishers
  • Ride-On Scrubbers
  • Ride-On Sweepers
  • Upright Vacuums
  • Walk-Behind Sweepers and more...

Small Engines
  • Cart Pushers
  • Golf Carts
  • Golf Club Cars
  • Pallet Jacks
  • Pressure Washers
  • Scissor Lifts
  • Store Shopping Mobility Carts
  • Tugs and more...

Planned Maintenance (PM) Service

Minor problems are detected and corrected before they become a major problem, requiring a costly service call. For example, one of the major costs incurred on equipment due to lack of PM service is a drastic reduction in battery life due to under filled batteries or batteries that have been filled with tap water. In addition, another cause of major repairs or engine replacements on propane powered buffers is failing to change the engine oil regularly or running the equipment low on oil and not cleaning or changing the filters on a regular basis. Your equipment will run longer and at a reduced cost if it is properly maintained and extending the life of your equipment.

Propane Buffer PM Service (Plan Maintenance)

SUBSYSTEM CHECKLIST
  1. Change oil & filter
  2. Remove all shrouds & clean cooling fins
  3. Check for oil leaks
  4. Inspect / clean air filter & pre-cleaner
  5. Inspect / clean debris filter
  6. Check fuel lines for leaks w/ soap solution
  7. Torque all head bolts to manufacturer's specification
  8. Inspect spark plugs / replace as needed
  9. Check & tighten all nuts/bolts
  10. Check & clean battery connections
  11. Inspect Grommet and Dust Bag
SYSTEM CHECKLIST
  1. Inspect & adjust drive belts / replace as needed
  2. Inspect & belt tensioner & pulley
  3. Inspect Pad Driver and Pad Driver/Face/Pad Holder
  4. Check Front end assembly and lube bearings
  5. Check wheels & bearings
  6. Check / adjust / lube throttle cable
  7. Check engine RPM at high speed / adjust as needed
  8. Check engine RPM to proper specification at idle
  9. Perform A C.o. emissions test / record results
  10. Check all phase and Proper operations
  11. Wipe down entire unit w/ cleaner

Ride On Scrubbers PMs Service (Plan Maintenance)

  1. Batteries-Hydrometer Test, Clean Cables and Tighten all battery connections, Fill cells as needed
  2. Spray with Protectant Terminals/Post and Cables
  3. Load Test Batteries
  4. Check Battery Charger for Battery Operations
  5. Check Charger Plugs for Damages
  6. Check Switches and Gauges
  7. Check Vac Motor for Proper Operations
  8. Check/Clean/Replace Vac Filter
  9. Check All Vac Hoses and Drain Hoses or Replace as Needed
  10. Check and Clean Solution Valves if Possible
  11. Inspect all Solutions Lines and Connections
  12. Inspect Squeegee Blades/Rotate/Replace as Needed
  13. Adjust Squeegee Assy And Check Squeegee Caster Wheels
  14. Check and Tighten All Nuts and Bolts
  15. Lubricate All Pivots and Joint
  1. Check Brush Drive Motors and Carbon Brushes
  2. Check Retainers and Skirts
  3. Check Pad Drivers and Pad Holders
  4. Check Steering Assy and Adjust as Needed
  5. Check Brake System for Proper Operations
  6. Check Drive Wheels Assy and Carbon Brushes as Needed
  7. Check Emergency Brake for Proper Operations
  8. Check Drive Chain/Adjust/ Lube as Needed
  9. Inspect All Belts and Adjust/ Crack Free
  10. Check Electrical System and Wiring Harness
  11. Grease All Zerk and Fittings
  12. Check Float Assembly for Proper Operations
  13. Check Vac System Gaskets and Seals
  14. Check All Phases and Check for Proper Operations
  15. Clean and Wipe Down the Entire Unit with Cleaner.

Walk Behind Scrubber PMs Service (Plan Maintenance)

  1. Batteries-Hydrometer Test, Clean Cables and Tighten all battery connections, Fill cells as needed
  2. Spray with Protectant Terminals/Post and Cables
  3. Load Test Batteries
  4. Check Battery Charger for Battery Operations
  5. Check Charger Plugs for Damage
  6. Check Switches and Gauges
  7. Check Vac Motor for Proper Operations
  8. Check/Clean/Replace Vac Filter
  9. Check All Vac Hoses and Drain Hoses or Replace as Needed
  10. Check and Clean Solution Valves if Possible
  11. Inspect all Solutions Lines and Connections
  12. Inspect Squeegee Blades/Rotate/Replace as Needed
  13. Adjust Squeegee Assy And Check Squeegee Caster Wheels
  14. Check and Tighten All Nuts and Bolts
  15. Lubricate All Pivots and Joints
  1. Check Brush Drive Motors and Carbon Brushes
  2. Check Retainers and Skirts
  3. Check Pad Drivers and Pad Holders
  4. Check Triggers and Handle
  5. Check Caster Wheels and Grease as needed
  6. Check Drive Wheels Assy and Carbon Brushes as Needed
  7. Check Emergency Brake for Proper Operations
  8. Check Drive Chain/Adjust/ Lube as Needed
  9. Inspect All Belts and Adjust/ Crack Free
  10. Check Electrical System and Wiring Harness
  11. Grease All Zerk and Fittings
  12. Check Float Assy for Proper Operations
  13. Check Vac System Gaskets and Seals
  14. Check All Phases and Check for Proper Operations
  15. Clean and Wipe Down the Entire Unit with Cleaner

Warranty Service

We are authorized for warranty repair on Minuteman International and Amigo Mobility International. We also offer planned maintenance (PM) to help keep your equipment repair cost and downtime to a minimum.